Bendi Forklifts
LANDOLL CORPORATION
BENDI FORKLIFTS
The Landoll Bendi forklifts are articulating, AC powered or internal combustion, narrow aisle forklifts maximizing cube utilization while providing front loader versatility. Maximum space utilization, increased productivity, operator comfort and safety are the primary benefits.
BENDI FORKLIFTS
B3/30AC
The Bendi model B3/30AC works in aisles as narrow as *72″ (1.8M), has a basic capacity of 3,000 lbs. (1361kg) at 24″ (600mm) load center and has lift heights available to 30′ (9.14M).
The Bendi B3/30AC is a 3-wheel articulating forklift with a single poly front drive tire and solid rubber rear tires. Front articulation of 220°, narrow mast and a compact front end allow easy stacking in Very Narrow Aisles. The B3/30AC can work inside and outside on paved surfaces. The B3/30AC does all the jobs of a reach truck in aisles at least 40″ (1M) smaller.
B3/30AC
Specifications
- Three-Wheel Design, Single Front Wheel Drive
- 9.75” (248mm) Stroke Integral Side Shifter
- 220˚ Front End Rotation
- Adjustable Seat and Steering Wheel
- DuraSteerTM Front Wheel Hydraulic Steering
- AC Traction Motor Controller with LandActive Control (LandActive control provides additional control during stacking as the maximum truck speed is controlled by steering angle.)
- AC Hydraulic Motor Controller
- Interactive LCD Status Monitor
- BDI with Lift Interrupt, Hour Meter with Service Monitor, Diagnostic Code Display, Input Device Calibration
- Hydraulic Rear Wheel Brakes
- Safety Seat Switch and Seat Belts
- 40” (1000mm) Tapered Tip Forks – Rear Tow Pin
- Hand Actuated Parking Brake
- Creep Speed Mode Selection Switch
- High Visibility Mast and 36” (914mm) High Backrest
- Mast Tilt 1º Forward and 2º Backward
- 48 Volt Electrical System
- Three Section Hydraulic Control Valve
- Smooth Poly Front Drive Tire and Rubber Rear Tires
- Horn, Key Switch and Hour Meter
- Meets ANSI B56.1
BENDI FORKLIFTS
B30AC & B40AC
The Bendi model B30AC/B40AC works in aisles as narrow as *78″ (1.98M), has a basic capacity starting at 3,000 lbs. (1361 kg) at 24″ (600mm) load center and has lift heights available to 26′ (7.92M).
The Bendi B30AC/B40AC is a 4-wheel articulating forklift with dual independently driven rear-drive tires and soft-poly front load tires. Excellent traction, braking and power enable climbing steep ramps with loads. Three or four stage masts are available making this unit excellent for loading/unloading trailers and containers. The B30AC/B40AC can also work inside and outside on paved surfaces and has a floating front axle allowing the truck to ride smoothly over uneven floors. The Bendi B30AC/B40AC does all of the jobs of reach and counterbalanced trucks but in much narrower aisles
B30AC & B40AC
Specifications
- 3,000 lb. (1361kg) and 4,000 lb. (1814kg) Capacity at 24″ (600mm) Load Center
- Four-Wheel Design, Dual Rear Wheel Drive Provides Excellent Power, Braking and Traction
- Ergonomic Design for Exceptional Operator Comfort and Safety
- Integral Wide Stroke Sideshifter Makes Placing and Picking Loads Effortless
- DuraSteerTM Front Wheel Hydraulic Steering Provides Smooth, Reliable, Long-Lasting Steering Control
- Independently Controlled Rear Wheels Allow Independent Speed Control of Each Drive Tire Based on Steering Angle
- Creep Speed Mode Adds Enhanced Control when Handling Loads at High Elevations or While Training Operators
- High Visibility Mast Allows Optimum Safety and Control
- AC Traction and Hydraulic Motors Ensure Minimal Maintenance and High Efficiency
- High-Efficiency Curtis AC Controllers Provide Trouble Free Operation
- Interactive LCD Status Monitor (BDI with Lift Interrupt, Hour Meter with Service Monitor, Diagnostic Code Display, Input Device Calibration)
- 48 Volt Electrical System
- Optional Cold Storage Conditioned to -22°F (-30°C)
BENDI FORKLIFTS
B40AC-DR & B50AC-DR
The Bendi model B40AC-DR / B50AC-DR will stack loads two deep in aisles as narrow as *96” (2.4 M) has a basic starting capacity of 2,500 lbs. (1,136 kg) at 24” (600 mm) load center and has lift heights available to 35′ 5″ (10.80 M). The reach from face to mast is 52” (1,321 mm) and the integral pantograph reach stroke is 41” (1,041 mm) The B40AC-DR / B50AC-DR has a 33” (838 mm) wide tilting and side shifting fork carriage.
The Bendi B40AC-DR / B50AC-DR is a 4-wheel articulating forklift with dual independently driven rear-drive tires and soft-poly front load tires. The B40AC-DR / B50AC-DR can work inside and outside on paved surfaces and has a floating front axle allowing the truck to ride smoothly over uneven floors. The B40AC-DR / B50AC-DR does all of the jobs of a reach and counterbalanced truck but in much narrower aisles.
B40-DR & B50AC-DR
Specifications
- Four Wheel Design, Dual Rear Wheel Drive
- 8” (200 mm) Stroke Integral Side Shifter
- 41” (1041 mm) Stroke Integral Pantograph Reach
- 52” (1321 mm) Reach From Face of Mast
- 33” (838 mm) Wide Tilting and Side Shifting Fork Carriage
- Adjustable Seat and Steering Wheel
- Rotation via DuraSteerTM Actuator, with 5-Year Warranty on Articulatio
- Dual Curtis AC Traction Motor Controllers
- Curtis AC Hydraulic Motor Controller
- Battery Discharge Indicator with Slow Alert
- Hydraulic Disk Brakes
- “Floating” Articulated Front Axle
- One Parts and Operator’s Manual Included
- Curtis Engage Dash Display
- Hand Actuated Parking Brake
- 36” (914mm) High Backrest
- High Visibility Mast
- 170˚ Rear View Mirror
- Safety Seat Switch and Seat Belt
- Fixed Mast with Carriage Tilt of 3º Fwd / 4º Rwd
- 48 Volt Electrical System
- Three Section Hydraulic Control Valve
- Smooth Rubber Drive Tires
- Soft Polyurethane Load Wheel Tires
- 40” Tapered Tip Forks – Rear Tow Hitch Pin
- Meets ANSI B56.1
BENDI FORKLIFTS
B55AC
The Bendi model B55AC works in aisles as narrow as *84″ (2.13M). The B55AC high volume model has a basic capacity of 5,500 lbs. (2495kg) at 24″ (600mm) load center and has lift heights available to 30′ (9.14M).
The B55AC model is a 4-wheel articulating forklift with dual independently driven rear-drive tires and soft-poly front load tires. Excellent traction, braking and power enable climbing steep ramps with loads. Three or four stage masts are available. The B55AC can work inside and outside on paved surfaces and have a floating front axle, allowing the truck to ride smoothly over uneven floors and do the jobs of reach and counterbalanced trucks but with much heavier loads and in much narrower aisles.
B55AC
Specifications
- 5,500 lb. (2,495kg) Capacity
- Lift Heights to 360” (9.14M)
- 84” (2.13M) Stacking Aisle with 48” (1,200mm) Long Load
- High Visibility 3-Stage or 4-Stage Mast
- Integral 11.2” (285mm) Stroke Side Shifter and 36” (914mm) High Load Backrest
- Dual Inside / Outside Capability
- Articulated Floating Front Axle, 48” (1,219mm) Wide
- Large Diameter Smooth Rubber Drive Tires
- Polyurethane Load Tires
- 180° Front-End DuraSteer™ Articulation Steering Assembly with 5-Year Warranty
- Heavy Duty Dual Rear Wheel Planetary Drives
- AC Traction and Hydraulic Controllers
- Powerful AC Drive and Hydraulic Motors
- Comfortable Seated Operation with All Truck Controls in Easy Reach
- Full Diagnostic Intelligent Display with Battery Discharge Indicator and Hour Meter
- Adjustable Cloth Suspension Swivel Seat
- Armrest, Adjustable Steering Column, Key Switch, Horn and Seat Belt
- Hydraulic Power Steering
- 4-Post Heavy-Duty Overhead Guard
- Safety Deadman Seat Switch
- Heavy Duty Unitized Robotic Welded Chassis Design
- Provisions for RF Terminals Provided
- Accepts Class II Attachments
- Easily Accessible Components for Low Cost Maintenance
BENDI FORKLIFTS
B40i5
The Bendi model B40i5 works in aisles as narrow as *78″ (1.98M), has a basic capacity of 4,000 lbs. (1814kg) at 24″ (600mm) load center and has lift heights available to 30′ (9.14M). The LP Gas engine provides the ability to run 24/7 without battery changing or charging.
The B40i5 is a 4-wheel articulating forklift with dual rear-drive tires and soft-poly front load tires. The hydrostatic drive provides excellent traction and braking, high-speed capability and power to enable climbing steep ramps with loads. Three or four stage masts are available making this unit excellent for loading/unloading trailers, containers and highway trailers. The B40i5 can work inside and outside on paved surfaces and has a floating front axle allowing the truck to ride smoothly over uneven floors. The Bendi B40i5 does all of the jobs of reach and counterbalanced trucks but in much narrower aisles.
B40i5
Specifications
- 4,000 lb. (1,814kg) Capacity at 24” (600mm) Load Center
- Tier III Certified, LP Gas, 2.5L, Kubota Industrial Engine
- Gear Driven Valve Train – No Belts or Chains
- CAN-Bus Electronics for Integrated Control of Drive, Lift and Steering
- Simplified Maintenance, Diagnostics and Calibration through Dash Display
- Dash Display with Hour Meter, Fuel Gauge and Engine Monitoring
- Via-Sonic Fuel Level Sensor with 99.5% Accuracy
- Heavy Duty Dual Rear Wheel Hydraulic Motors
- Automatic Hydrostatic Braking and Foot Activated Hydraulic Parking Brake
- Lift Heights to 360” (9.14M)
- 78” (1.98M) Stacking Aisle with 48” (1,219mm) Long Load
- High Visibility 3-Stage or 4-Stage Mast
- Integral 11.2” (285mm) Stroke Sideshifter and 36” (914mm) High Load Backrest
- Dual Indoor / Outdoor Capability
- Articulated 42” (1,067mm) Wide Floating Front Axle
- Large Diameter Smooth Rubber Drive Tires
- Polyurethane Load Tires
- 180° Front-End “DuraSteer” Articulation / Steering Assembly with Extended Warranty
- Comfortable Seated Operation with all Truck Controls within Easy Reach
- Adjustable Vinyl Suspension Swivel Seat
- Armrest and Adjustable Steering Column, Key Switch, Horn and Seat Belt
- Hydraulic Power Steering
- 4-Post Heavy-Duty Overhead Guard
- Safety Deadman Seat Switch
- Heavy Duty Unitized Robotic Welded Chassis Design
- Provisions for RF Terminals Provided
- Accepts Class II Attachments
- Easily Accessible Components for Low Cost Maintenance